Influence of limiting the duration of the armature winding current on the operating indicators of a linear pulse electromechanical induction type converter
DOI:
https://doi.org/10.20998/2074-272X.2021.6.01Keywords:
linear pulse electromechanical converter of induction type, shock-power device, electromechanical accelerator, performance indicators, limiting the duration of the armature winding currentAbstract
Introduction. Linear pulse electromechanical converters of induction type (LPECIT) are used in many branches of science and technology as shock-power devices and electromechanical accelerators. In them, due to the phase shift between the excitation current in the inductor winding and the induced current in the armature winding, in addition to the initial electrodynamic forces (EDF) of repulsion, subsequent EDF of attraction also arise. As a result, the operating indicators of LPECIT are reduced. The purpose of the article is to increase the performance of linear pulse electromechanical induction-type converters when operating as a shock-power device and an electromechanical accelerator by limiting the duration of the induced current in the armature winding until its polarity changes. Methodology. To analyze the electromechanical characteristics and indicators of LPECIT, a mathematical model was used, in which the solutions of equations describing interrelated electrical, magnetic, mechanical and thermal processes are presented in a recurrent form. Results. To eliminate the EDF of attraction between the LPIECIT windings, it is proposed to limit the duration of the induced current in the armature winding before changing its polarity by connecting a rectifier diode to it. It was found that when the converter operates as a shock-power device without limiting the armature winding current, the value of the EDF pulse after reaching the maximum value decreases by the end of the operating cycle. In the presence of a diode in the armature winding, the efficiency criterion, taking into account the EDF pulse, recoil force, current and heating temperature of the inductor winding, increases. When the converter operates as an electromechanical accelerator without limiting the armature winding current, the speed and efficiency decrease, taking into account the kinetic energy and voltage of the capacitive energy storage at the end of the operating cycle. In the presence of a diode in the armature winding, the efficiency criterion increases, the temperature rise of the armature winding decreases, the value of the maximum efficiency increases, reaching 16.16 %. Originality. It has been established that due to the limitation of the duration of the armature winding current, the power indicators of the LPECIT increase when operating as a shock-power device and the speed indicators when the LPECIT operates as an electromechanical accelerator. Practical value. It was found that with the help of a rectifier diode connected to the multi-turn winding of the armature, unipolarity of the current is ensured, which leads to the elimination of the EDF of attraction and an increase in the performance of the LPECIT.
References
Balikci A., Zabar Z., Birenbaum L., Czarkowski D. Improved performance of linear induction launchers. IEEE Transactions on Magnetics, 2005, vol. 41, no. 1, pp. 171-175. doi: https://doi.org/10.1109/TMAG.2004.839283.
Go B., Le D., Song M., Park M., Yu I. Design and Electromagnetic Analysis of an Induction-Type Coilgun System With a Pulse Power Module. IEEE Transactions on Plasma Science, 2019, vol. 47, no. 1, pp. 971-976. doi: https://doi.org/10.1109/TPS.2018.2874955.
Vilchis-Rodriguez D.S., Shuttleworth R., Barnes M. Modelling Thomson Coils With Axis-Symmetric Problems: Practical Accuracy Considerations. IEEE Transactions on Energy Conversion, 2017, vol. 32, no. 2, pp. 629-639. doi: https://doi.org/10.1109/TEC.2017.2651979.
Bolyukh V.F., Katkov I.I. Cryogenic Cooling System “KrioBlast” Increased Efficiency and Lowered the Operation Time of Protective Electrical Induction-Induced Devices. Proceedings of the ASME 2013 International Mechanical Engineering Congress and Exposition. Volume 8B: Heat Transfer and Thermal Engineering. San Diego, California, USA. November 15-21, 2013. V08BT09A003. ASME. doi: https://doi.org/10.1115/imece2013-62383.
Zhou Y., Huang Y., Wen W., Lu J., Cheng T., Gao S. Research on a novel drive unit of fast mechanical switch with modular double capacitors. The Journal of Engineering, 2019, vol. 2019, no. 17, pp. 4345-4348. doi: https://doi.org/10.1049/joe.2018.8148.
Liu X., Yu X., Ban R., Li Z. Analysis of the Capacitor-Aided Meat Grinder Circuits for an Inductive Pulsed Power Supply. IEEE Transactions on Plasma Science, 2017, vol. 45, no. 7, pp. 1339-1346. doi: https://doi.org/10.1109/TPS.2017.2705179.
Kondratenko I.P., Zhyltsov A.V., Pashchyn N.A., Vasyuk V.V. Selecting induction type electromechanical converter for electrodynamic processing of welds. Technical Electrodynamics, 2017, no. 5, pp. 83-88. (Ukr). doi: https://doi.org/10.15407/techned2017.05.083.
Soda R., Tanaka K., Takagi K., Ozaki K. Simulation-aided development of magnetic-aligned compaction process with pulsed magnetic field. Powder Technology, 2018, vol. 329, pp. 364-370. doi: https://doi.org/10.1016/j.powtec.2018.01.035.
Gorodzha K.A., Podoltsev A.D., Troshchynckyi B.O. Electromagnetic processes in pulsed electrodynamic emitter to excite elastic vibrations in concrete structures. Technical Electrodynamics, 2019, no. 3, pp. 23-28. (Ukr). doi: https://doi.org/10.15407/techned2019.03.023.
Bolyukh V.F., Oleksenko S.V. The influence of the parameters of a ferromagnetic shield on the efficiency of a linear induction–dynamic converter. Russian Electrical Engineering, 2015, vol. 86, no. 7, pp. 425-431. doi: https://doi.org/10.3103/S1068371215070044.
Puumala V., Kettunen L. Electromagnetic design of ultrafast electromechanical switches. IEEE Transactions on Power Delivery, 2015, vol. 30, no. 3, pp. 1104-1109. doi: https://doi.org/10.1109/tpwrd.2014.2362996.
Bolyukh V.F., Schukin I.S., Lasocki J. Influence of the initial winding displacement on the indicators of the electromechanical induction accelerator of cylindrical configuration. Electrical Engineering & Electromechanics, 2021, no. 5, pp. 3-10. doi: https://doi.org/10.20998/2074-272X.2021.5.01.
Niu X., Li W., Feng J. Nonparametric Modeling and Parameter Optimization of Multistage Synchronous Induction Coilgun. IEEE Transactions on Plasma Science, 2019, vol. 47, no. 7, pp. 3246-3255. doi: https://doi.org/10.1109/tps.2019.2918157.
Kondratiuk M., Ambroziak L. Concept of the magnetic launcher for medium class unmanned aerial vehicles designed on the basis of numerical calculations, Journal of Theoretical and Applied Mechanics, 2016, vol. 54, no. 1, pp. 163-177. doi: https://doi.org/10.15632/jtam-pl.54.1.163.
Angquist L., Baudoin A., Norrga S., Nee S., Modeer T. Low-cost ultra-fast DC circuit-breaker: Power electronics integrated with mechanical switchgear. 2018 IEEE International Conference on Industrial Technology (ICIT), 2018, pp. 1708-1713. doi: https://doi.org/10.1109/icit.2018.8352439.
Bolyukh V.F., Dan’ko V.G., Oleksenko S.V. The Effect of an External Shield on the Efficiency of an Induction-Type Linear-Pulse Electromechanical Converter. Russian Electrical Engineering, 2018, vol. 89, no. 4, pp. 275-281. doi: https://doi.org/10.3103/S106837121804003X.
Bolyukh V.F., Katkov I.I. Influence of the Form of Pulse of Excitation on the Speed and Power Parameters of the Linear Pulse Electromechanical Converter of the Induction Type. Volume 2B: Advanced Manufacturing, Nov. 2019, 8 p. doi: https://doi.org/10.1115/imece2019-10388.
Bolyukh V.F., Shchukin I.S. Influence of an excitation source on the power indicators of a linear pulse electromechanical converter of induction type. Technical Electrodynamics, 2021, no. 3, pp. 28-36. doi: https://doi.org/10.15407/techned2021.03.028.
Ljutenko L.A., Mikhailov V.M. Expansion of cylindrical tubular workpieces on high-voltage magnetic-pulse installation with controlled vacuum discharger. Electrical Engineering & Electromechanics, 2021, no. 3, pp. 42-46. doi: https://doi.org/10.20998/2074-272X.2021.3.07
Bolyukh V.F., Kashanskyi Y.V., Shchukin I.S. Comparative analysis of power and speed indicators linear pulse electromechanical converters electrodynamic and induction types. Technical Electrodynamics, 2019, no. 6, pp. 35-42. (Rus). doi: https://doi.org/10.15407/techned2019.06.035.
Bolyukh V.F., Vinnichenko A.I. Concept of an Induction-Dynamic Catapult for a Ballistic Laser Gravimeter. Measurement Techniques, 2014, vol. 56, no. 10, pp. 1098-1104. doi: https://doi.org/10.1007/s11018-014-0337-z.
Bolyukh V.F., Omel’chenko A.V., Vinnichenko A.I. Effect of Self-Seismic Oscillations of the Foundation on the Readout of a Ballistic Gravimeter with an Induction-Dynamic Catapult. Measurement Techniques, 2015, vol. 58, no. 2, pp. 137-142. doi: https://doi.org/10.1007/s11018-015-0675-5.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2021 V.F. Bolyukh, I.S. Shchukin
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
Authors who publish with this journal agree to the following terms:
1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.